+61 415 779 146 Get a Quote ↗

Engineered Oak Flooring · French oak, 14mm · Sydney, NSW

Swish Oak Natura Handcrafted Engineered Oak Flooring

Swish Oak Natura Handcrafted is our engineered timber floors Sydney range with a hand-applied colour: genuine French oak boards 1900 x 190mm, 14mm thick with a 3mm oak wear layer, in three stained colours, Misty Quartz, Natural Canvas and Sunlit Sienna. Explore our stained oak floors Sydney wide, from Parramatta and Blacktown to Burwood, Bankstown and Liverpool. Choose a colour below, compare Handcrafted with our Natura and Contemporary oak flooring, or tell us about your rooms and we will call you to talk it through.

Swish Oak Natura Handcrafted colours

The range

Engineered Timber Floors Sydney: About Swish Oak Natura Handcrafted

Swish Oak Natura Handcrafted is a range of engineered oak flooring in three French oak colours. Each oak floorboard is 1900mm long, 190mm wide and 14mm thick, with a genuine 3mm French oak wear layer on multiple bonded layers of plywood, a tongue and groove profile and a micro-bevelled edge. The supplier describes the colour as coming from a manual, 144-hour reactive stain process with natural reactive dyes, such as apple fruit acid, grape tannin and lime, and no industrial pigments applied on top of the wood. If you are looking for stained oak floors, pale oak engineered flooring, 14mm wood flooring or European oak engineered flooring in Sydney, these boards arrive pre-finished, so there is no sanding or staining at your home. It is one of the ranges in our engineered timber and oak flooring collection.

The boards can be glued down or floated with glued joints, so we choose the method for your subfloor. The supplier says the layered construction resists the expansion and contraction of solid wood and rates the boards E1 for emissions, a low VOC engineered hardwood. Whether you are comparing oak timber floorboards, oak timber flooring, oak hardwood flooring, engineered wood flooring or engineered wood floorboards, or searching for engineered timber flooring Sydney, engineered flooring Sydney or engineered wood flooring Sydney, we supply and install Swish Oak Natura Handcrafted in homes and businesses across Sydney. Our engineered timber flooring range also includes the Swish Oak Natura, the Swish Oak Contemporary, the Swish Oak Wideboard and the Swish Oak Natura Herringbone, so you can compare them all.

Pick a colour

Swish Oak Natura Handcrafted Colours: Three Stained French Oak Floors

Every Swish Oak Natura Handcrafted colour has the same construction and specification. Click a colour to see it up close, with its details and a quote form. Seeing a sample in your own light is the easiest way to choose, so ask us when you call.

Colours are shown as photographed and may look different in your home. Product images may differ from the actual product.

The details

Swish Oak Natura Handcrafted Specifications

Here’s the technical detail for the whole Swish Oak Natura Handcrafted range, from the manufacturer’s information. It’s the same for every colour.

Swish Oak Natura Handcrafted engineered oak flooring: technical specifications
SpecificationSwish Oak Natura Handcrafted
TypeEngineered oak flooring
TimberGenuine French oak
Board size1900 x 190mm
Thickness14mm, with a 3mm French oak wear layer
ConstructionA 3mm genuine French oak wear layer on multiple bonded layers of plywood
Colour processThe supplier describes a manual, 144-hour reactive stain process using natural reactive dyes, such as apple fruit acid, grape tannin and lime, with no industrial pigments applied on top of the wood
GradeABCD
Surface finishPre-finished. The supplier lists UV matt lacquered or oiled coatings, without saying which applies to each colour
EdgeMicro-bevelled
ProfileTongue and groove
Installation methodGlued down, or floated with glued joints
Pack size2.90 m² (8 boards)
Pack weight25 kg
EmissionsLow VOC, rated E1 (under 5ppm)
Underfloor heatingListed by the supplier as compatible. Its installation guide puts engineered flooring over underfloor heating at the owner's and installer's risk, and its warranty excludes radiant heating
WarrantyThe supplier's Swish Oak warranty is 25 years residential for wear and structural integrity. This range isn't named in the 2023 catalogue, so we confirm the warranty for your colour with the supplier before you order

Colour process, construction and emissions

Swish Oak Natura Handcrafted Stained Engineered Oak Construction

Here is what the supplier says about how Swish Oak Natura Handcrafted is coloured and built, in our words. The supplier's published fire and slip test results cover its Swish Oak Wideboard line, not this range, so we don't show them here. Ask us if you need test results for a specification.

144HSTAINHAND

A 144-hour reactive stain process

The supplier describes the colour as coming from a manual reactive stain process using natural reactive dyes, which it says brings out the colour tones inside the wood. This is the supplier's description of its process.

Process
Manual reactive stain, 144 hours
Dyes
Natural, such as apple fruit acid, grape tannin and lime
Source
Product pages
View the supplier's catalogue (PDF) →
3MMOAKLAYER

A genuine 3mm French oak wear layer

The top layer of Swish Oak Natura Handcrafted is genuine French oak, 3mm thick, bonded to multiple layers of plywood to make a stable 14mm board.

Wear layer
3mm genuine French oak
Overall thickness
14mm
Grade
ABCD
View the supplier's catalogue (PDF) →
E1<5PPMVOC

Rated E1 for emissions

The product pages list a VOC rating of E1, under 5ppm, which the supplier describes as meeting international standards for high indoor air quality.

Rating
E1 (under 5ppm)
Applies to
Natura Handcrafted
Source
Product pages
View the supplier's catalogue (PDF) →

Specifications are from the supplier's product pages.

Why choose it

Swish Oak Natura Handcrafted Features and Benefits

Here’s what Swish Oak Natura Handcrafted gives you, and what to keep in mind.

Stained oak floors with a hand-applied colour

The supplier describes a manual reactive stain process that takes 144 hours and uses natural reactive dyes, such as apple fruit acid, grape tannin and lime, to bring out the colour tones already in the oak, without industrial pigments on top of the wood.

Genuine French oak, 190mm wide

These engineered oak planks, a 14mm wood flooring with a genuine 3mm French oak wear layer, are 1900mm long and 190mm wide, and the supplier says wide planks make an interior feel more spacious.

Stable engineered timber flooring

The oak sits on multiple bonded layers of plywood, which is what makes these engineered floorboards more stable than solid oak flooring. The supplier says the construction minimises expansion and contraction caused by humidity and temperature.

Pre-finished oak floorboards, with no sanding on site

These oak floorboards arrive pre-finished with UV lacquered or oiled coatings, so there is no sanding or staining at your home.

Float it or glue it down

These tongue and groove boards can be floated with glued joints or glued down, an engineered timber floating floor or a bonded floor, so we can choose the method that suits your subfloor.

Low emissions and a long warranty

The boards are rated E1 for emissions at under 5ppm, a low VOC engineered hardwood, and the supplier's Swish Oak warranty is 25 years residential, subject to its terms and correct installation.

Side by side

Handcrafted vs Natura and Contemporary Engineered Oak Flooring

Natura Handcrafted has the same board size and 3mm oak layer as our Natura range, and the difference is how it is coloured. This table compares it with Natura and with Contemporary, so you can compare stained oak floors with lacquered and brushed oak floors.

Swish Oak Natura Handcrafted compared with Swish Oak Natura and Swish Oak Contemporary
CompareNatura HandcraftedSwish Oak NaturaSwish Oak Contemporary
Colours3, coloured with a reactive stain16, with UV lacquered or oiled finishes6, brushed
Board size1900 x 190mm1900 x 190mm1900 x 190mm
Oak layer3mm genuine French oak3mm genuine French oak2mm solid French oak
Colour sourceA manual reactive stain with natural dyes, as the supplier describesNatural, brushed, hand-scraped or stained finishes, as listed by the supplierBrushed oak with a UV lacquer matt finish
InstallationTongue and groove, glued down or floated8 colours click lock, 8 tongue and grooveTongue and groove, floated or glued down

Figures are from the supplier's catalogue and product pages. Ask us to compare the floors for your rooms.

Warranty

Swish Oak Natura Handcrafted Engineered Oak Flooring Warranty

The supplier's Swish Oak warranty is 25 years residential for wear and structural integrity. Natura Handcrafted was added after the supplier's 2023 catalogue, which doesn't name it, so we confirm the warranty for your colour with the supplier before you order. Here is what the Swish Oak warranty covers, what it asks of you and what it leaves out, in our words. It is in addition to your rights under the Australian Consumer Law.

Swish Oak warranty, as published by the supplier
CoverResidential
Wear and structural integrity25 years
Manufacturing defects at purchaseCovered

What it takes to keep the warranty

Installed to the instructions

The floor must be laid to the Swish Oak installation instructions and the adhesive manufacturer's instructions, and boards with obvious defects must not be installed.

Used inside, and kept dry

The warranty applies to floors laid internally and not subject to excessive moisture, kept in their original state and maintained as the care instructions say.

Kept in stable conditions

The warranty asks for a year-round humidity of 40 to 60%.

The original buyer

The warranty extends to the buyer and the owner of the first structure the floor is installed in, and can't be transferred.

What the warranty doesn’t cover

Moisture problems

Subfloor moisture, leaks, rain and wet mopping, and gapping, cupping or crowning from moisture getting in or out.

Sun and natural variation

Colour change and fading from sunlight, and variation in colour, grain and markings that exist when new or develop over time.

Underfloor and radiant heating

The warranty doesn't apply to floors installed over radiant floor heating, even though the supplier lists the floor as compatible.

Damage and misuse

Abuse, neglect, solvents, chemicals, point loads, stiletto heels, unpadded furniture feet, and damage from sand, pebbles or other abrasives.

Natural characteristics

Fine surface checking, gloss variation between boards, and colour variation between boards.

Stains, finishes and changes

Stains and finishes, alterations to the product, insect infestation after shipment, and flooring installed with visible defects.

This is a summary of the warranty conditions in the supplier's 2023 catalogue, and the supplier's warranty terms apply.

Before we lay

Subfloor and Site Requirements for Swish Oak Natura Handcrafted

Engineered timber flooring installation starts with the floor underneath, because oak moves with moisture and temperature. These are the requirements in the supplier's tongue and groove installation guide (2017), in our words, and we check each one before we quote.

Dry interior areas only

The warranty applies to floors laid internally and not subject to excessive moisture, and the supplier recommends Swish Oak for dry interior areas, not bathrooms or laundries.

Stable room conditions

The room should be at least 18°C with 40 to 60% humidity for at least 14 days before, during and after installation, and the packs are stored unopened in the room for at least 7 days beforehand.

Concrete must be dry

A cement screed must not exceed 3% on the Tramex Concrete Encounter red scale. A PU primer or liquid DPM can seal slabs up to 6%. Pump or anhydrite screeds must be below 0.3% CM, and primers aren't suitable over them.

A suitable timber subfloor

Kiln-dried PAO battens (about 10 to 12%) no more than 300mm apart, flooring grade plywood or OSB Grade 3. Construction plywood and rough battens aren't suitable because of their moisture content.

A moisture barrier over cement

Always use builder's polythene or a suitable moisture barrier over cement floors, overlapped by 30cm, taped with waterproof tape and taken up the wall behind the skirting.

A flat, clean subfloor

Flat to 5mm over 3m, clean and secure. For glue down, the surface must be sound but porous, with sealers and old adhesive removed.

Room for movement

Leave a 15mm expansion gap at walls and fixed objects. A floating floor can run up to 8m in any direction before it needs an expansion joint, and heavy fixed items such as an island bench must not be fixed through it.

Underfloor heating

The supplier says the floor is suitable, but over underfloor heating it is at the owner's and installer's risk, and the warranty excludes radiant heating. The screed must stay under 26°C, with heating changes of no more than 5°C a day. We explain both before you decide.

The full requirements are in the supplier's installation guide, which also covers nail down, a method that isn't suitable for boards 190mm wide. We install to the guide and to the adhesive manufacturer's instructions.

Keeping it looking good

Looking After Your Swish Oak Natura Handcrafted Floor

An engineered oak floor lasts longer when you follow a few simple habits. These come from the manufacturer’s care guide, in our words.

Sweep or vacuum regularly

Use a vacuum, broom or antistatic mop to remove dust and grit, which scratch the finish of any engineered timber floorboards. Check that a vacuum's rollers can't scratch the oak.

Damp mop, never soak

The supplier's cleaning instructions for Swish Oak say to wash periodically with a damp mop and a quality non-abrasive wood floor cleaner made for UV prefinished floors. The floor must not get soaking wet.

No steam mops

The supplier says Swish Oak must not be cleaned with steam mops.

Protect the floor from furniture

Use protective pads and castor cups under chairs and furniture legs. Never slide heavy furniture, and for a fridge or piano, put a piece of carpet face down under the legs and pull on the carpet.

Mats that suit oak

Put a doormat at every outside door to catch dirt and absorb moisture, and never use a rubber mat, or one with a Styrofoam or plastic backing.

Keep the room comfortable

Oak likes a room at about 20°C and about 50% humidity, and a humidity controller may be needed. The warranty asks for a year-round humidity of 40 to 60%.

The supplier's documents

These are the supplier's own documents for Swish Oak, on its website. We've summarised what matters on this page, and the originals carry the full detail.

How it works

Swish Oak Natura Handcrafted Engineered Oak Flooring Installation in Sydney

Engineered timber flooring installation depends on the floor underneath, the conditions in the room and the method that suits your subfloor, so we check the subfloor first and then float or glue down each floor the way the supplier's guide requires. We install Swish Oak Natura Handcrafted across Sydney, and you can see where on our service areas page. Find out more about our floor installation service.

  1. We measure and inspect

    We measure your rooms, add 5% for cutting waste, and check the subfloor with a moisture meter. The supplier recommends a professional flooring contractor who owns a moisture meter, because checking the concrete and the house conditions is the installer's job.

  2. We test and prepare the subfloor

    A concrete slab must read no more than 3% on a Tramex Concrete Encounter red scale, and the surface must be flat to 5mm over 3m, clean, dry and secure. Cement floors get builder's polythene as a moisture barrier, overlapped by 30cm and taped.

  3. We let the boards settle

    The packs are stored flat and unopened in the room for at least 7 days before installation. The room needs to be at least 18°C with 40 to 60% humidity for at least 14 days before, during and after the job.

  4. We float or glue down the boards

    Engineered timber flooring installation here is either floating or glued down. A floating floor has a full line of PVA glue in the groove on the long sides and the short ends, clamp straps every 6 to 8 rows and 24 hours before foot traffic. A glued-down floor uses a suitable flexible adhesive and a notched trowel. Both leave a 15mm expansion gap.

  5. We finish the details

    Boards are blended from several cartons, expansion profiles go in at doorways, trims cover the gap, and we leave a few spare planks with you for future repairs.

Questions we get asked

Swish Oak Natura Handcrafted Engineered Oak Flooring FAQs

What is Swish Oak Natura Handcrafted engineered oak flooring?

Swish Oak Natura Handcrafted is our three-colour range of stained oak engineered timber flooring: genuine French oak boards 1900mm long and 190mm wide, 14mm thick with a 3mm oak wear layer, coloured with a manual reactive stain process. We supply and install it across Sydney.

What is a reactive stain?

The supplier describes a manual, 144-hour reactive stain process that uses natural reactive dyes, such as apple fruit acid, grape tannin and lime, to bring out the colour tones already in the oak, with no industrial pigments applied on top of the wood. That is the supplier's description, and we can show you the boards so you can judge the result.

Are stained oak floors durable?

The boards are pre-finished with UV lacquered or oiled coatings, and the supplier describes them as tough and longer lasting. Like any oak floor, they need pads under furniture, mats at the doors and the right cleaner for the finish, so ask us which finish your colour has.

Is sanding engineered hardwood floors possible with a stained oak?

The 3mm oak wear layer limits how much a floor can be sanded, and sanding would remove the stained surface, so restaining engineered hardwood floors isn't something we'd plan on. Ask us how you would refinish or repair your floor before you choose.

What can be done with restoring engineered wood flooring?

Light scratches and wear can often be cared for with the right cleaner and furniture pads. Deeper damage depends on the finish and how much of the 3mm oak layer is left, so send us photos and we will advise. A damaged board may need replacing.

Do you have white oak flooring?

Handcrafted's palest colour is Misty Quartz. For white oak flooring, see Danish White and Nordic Limed in our Swish Oak Natura range, and we can lay samples side by side at our Granville showroom.

Is engineered oak flooring real wood?

Yes. The wear layer is genuine French oak, 3mm thick, so the surface you see and walk on is real oak, with natural grain, knots and colour variation.

Is it a floating floor or glued down?

Either. These tongue and groove boards can be floated, with a full line of PVA glue in the groove, or glued down with a suitable flexible adhesive. We choose the method for your subfloor and rooms.

Can engineered oak flooring go over underfloor heating?

The supplier lists the floor as compatible with underfloor heating, but its installation guide puts engineered flooring over underfloor heating at the owner's and installer's risk, and its warranty excludes radiant heating. We explain both before you decide.

Can I use engineered oak flooring in a kitchen, bathroom or laundry?

The supplier recommends Swish Oak for dry interior areas, and its warranty excludes moisture problems and wet mopping. We don't recommend it for bathrooms or laundries. We check each room before we quote.

What does the subfloor need?

It must be flat to 5mm over 3m, clean, dry and secure. A concrete slab must read no more than 3% on a Tramex Concrete Encounter red scale and needs a polythene moisture barrier, and timber subfloors must be kiln-dried battens, flooring grade plywood or OSB Grade 3.

Is it a low VOC engineered hardwood?

The product pages list a VOC rating of E1, under 5ppm, which the supplier describes as meeting international standards for high indoor air quality.

How much does engineered timber flooring cost in Sydney?

There is no single price. It depends on the colour, the floor area, the existing floor, the preparation needed and the installation method. Send your suburb, room sizes and a few photos, or visit our showroom, and we will quote your engineered oak flooring job.

Is the oak sustainably sourced?

The supplier's product pages say the raw materials are FSC sustainable, while its technical data sheet for the Wideboard line lists PEFC. Ask us for the certificate, and we will get it from the supplier.

Do you supply and install engineered timber floors in Sydney?

Yes. We supply and install engineered timber flooring Sydney homes and businesses choose, whether you call it engineered flooring Sydney or engineered wood flooring Sydney, including engineered oak flooring and European oak engineered flooring in French oak, across Parramatta, Blacktown, Burwood, Bankstown, Liverpool and the suburbs around them. Tell us your suburb and we will confirm we can get to you.

Ready when you are

Get a Quote for Swish Oak Natura Handcrafted Engineered Oak Flooring

Tell us your suburb, the rooms you’re thinking about and the colour you like. We’ll call you, talk through the options and put a quote together for your place.

Areas we service

Request your quote

A short form. We’ll call you back to talk it through.

Please enter your name.
Please enter a valid number.
Please check your email address.
Please add your suburb.
Please choose one.

We use your details only to respond to your enquiry.

Thanks, we’ve got it.

Our team will call you to talk about your flooring.